CAS commercial gas and diesel compressors are designed for applications that require air on the go. The units are designed with durability and reliability in mind. The features of the CAS gas and diesel driven compressors are designed to make these compressors simpler to use and easier to maintain than any other compressor in this class. The engine is standard on the drivers side of the vehicle. No more walking all the way around the truck to start the compressor. The unloader is at your finger tip so you can unload the compressor before starting. This means your solenoid and starter will last much longer. The transfer tube is protected by the receiver.

All units include the following features:

• Solid cast iron pump
• Head unloaded
• Low rpm
• Disc and spring valves
• Centrifugal unloader
• Low pump rpm
• Oil sight glass
• Oil drain and fill on front of
  compressor pump

• 70% duty cycle
• OSHA style totally enclosed belt guard
• ASME code receivers
• On board battery with recharge system
• Automatic tank drain
• Belt guard aftercooler
• Vibration pads

• Heavy duty two stage solid cast iron pump
• Disk and spring valves
• Bearings on both ends of the crank shaft
• Centrifugal unloader
• Needle bearings and inserts on rods
• Industrial grade gas engine
• ASME tested powder coated tank
• 2 grove B width drive pulley
• Access to compressor valves without compressor head removal
• Pilot valve continuous operation
• Fully enclosed belt guard
• Full saddle mounting feet instead of pegged mounting feet
• Alternator on drive engine
• Torrington needle bearings
• Swedish steel valves
• Critical controls protected by compressor base plate
• Drive engine on left side for easy start up
• Heavy duty air filter

• Belt guard aftercooler (removes 60-70% moisture)
• On-board battery mounted and wired (no wiring to the front of the truck needed)
• Automatic tank drain
• Vibration pads

CAS commercial gas and diesel compressors are designed for applications that require air on the go. The units are designed with durability and reliability in mind. The features of the CAS gas and diesel driven compressors are designed to make these compressors simpler to use and easier to maintain than any other compressor in this class. The engine is standard on the drivers side of the vehicle. No more walking all the way around the truck to start the compressor. The unloader is at your finger tip so you can unload the compressor before starting. This means your solenoid and starter will last much longer. The transfer tube is protected by the receiver.

All units include the following features:

• Solid cast iron pump
• Head unloaded
• Low rpm
• Disc and spring valves
• Centrifugal unloader
• Low pump rpm
• Oil sight glass
• Oil drain and fill on front of
  compressor pump

• 70% duty cycle
• OSHA style totally enclosed belt guard
• ASME code receivers
• On board battery with recharge system
• Automatic tank drain
• Belt guard aftercooler
• Vibration pads

CAS commercial gas and diesel compressors are designed for applications that require air on the go. The units are designed with durability and reliability in mind. The features of the CAS gas and diesel driven compressors are designed to make these compressors simpler to use and easier to maintain than any other compressor in this class. The engine is standard on the drivers side of the vehicle. No more walking all the way around the truck to start the compressor. The unloader is at your finger tip so you can unload the compressor before starting. This means your solenoid and starter will last much longer. The transfer tube is protected by the receiver.

All units include the following features:

• Solid cast iron pump
• Head unloaded
• Low rpm
• Disc and spring valves
• Centrifugal unloader
• Low pump rpm
• Oil sight glass
• Oil drain and fill on front of
  compressor pump

• 70% duty cycle
• OSHA style totally enclosed belt guard
• ASME code receivers
• On board battery with recharge system
• Automatic tank drain
• Belt guard aftercooler
• Vibration pads

CAS commercial gas and diesel compressors are designed for applications that require air on the go. The units are designed with durability and reliability in mind. The features of the CAS gas and diesel driven compressors are designed to make these compressors simpler to use and easier to maintain than any other compressor in this class. The engine is standard on the drivers side of the vehicle. No more walking all the way around the truck to start the compressor. The unloader is at your finger tip so you can unload the compressor before starting. This means your solenoid and starter will last much longer. The transfer tube is protected by the receiver.

All units include the following features:

• Solid cast iron pump
• Head unloaded
• Low rpm
• Disc and spring valves
• Centrifugal unloader
• Low pump rpm
• Oil sight glass
• Oil drain and fill on front of
  compressor pump

• 70% duty cycle
• OSHA style totally enclosed belt guard
• ASME code receivers
• On board battery with recharge system
• Automatic tank drain
• Belt guard aftercooler
• Vibration pads